Data Sheet
|
1 |
Model No. |
WNA-1 |
|
2 |
Material |
T2 Copper |
|
3 |
Power |
1000W-3000W +5%, -10% |
|
4 |
Voltage |
220V-240V/50Hz. 110V/60Hz |
|
5 |
Hi-pot test |
1,800V/S min cold condition |
|
6 |
Leakage Current |
0.75ma max |
|
7 |
Insulation |
100MΩ |
|
8 |
Heating wire |
Ocr25AI5, Cr20NI80 or as custom's requirement |
|
9 |
Thermostat |
With 16A 250V. L=275mm. Double safety thermostat |
|
10 |
Total Length |
300mm |
|
11 |
Flange |
Brass.1 1/4" with/without anode holding M6/M8 |
|
12 |
Warranty |
1 Year |
Description
Immersion heater is a cost effective and ecologically sound method for heating material and provide a clean source of energy without leaving residual discharge or pollutants.
The length of T2 Copper Immersion Heater Elements can be customized.It is equipped with brass 1 1/4" flange and double safety thermostat.The power can also be customized.
This T2 copper immersion heater elements is high surface load products and working in the liquid. we use advanced manufacturing technology to make sure the safety and long servicelife Characteristic: These types of heaters are mainly work in to customers' different requirements of corrosion resistance, it can be made of stainless steel.copper.
Copper is usually used for solar water heater element because it is a good conductor of heat and electricity. It is also corrosion-resistant and has good thermal conductivity, it is an ideal water heating applications.
Copper solar water heater element has shapes and sizes, which depend on the volume of the solar water heater tank. They are used to heat the water for showers, washing dishes, and other household or industrial applications.
Before buying copper solar water heater element, there are several factors that you need to consider, including watt density, temperature, and fluid flow. Watt density refers to the amount of heat supplied by immersion element in a unit area. If you want this element to serve you for a long time, use the appropriate watt density.
Compared to other heating solution,the copper immersion heater element has high efficient,as it directly heat the liquid and water ,which deduct the heat loss.It can also be controlled by thermostats, sensors, or switches, to maintain the desired temperature and prevent overheating or underheating.
Copper immersion heater can be easily replaced and clean,it can be easily took out.
It can be easily assembled ,it can be assembled to the threaded opening or the flange fixed to the side of the tank or bottom.
No need more valves or pumps.
There are two points that should be paid attention to when the copper immersion heater is working :
1, the heating area can not be separated from the water surface and dry burning.
2. The heated water quality should not be too hard, and the scaling speed should not be too fast.
If the heating area is separated, the heat can not be absorbed by water in time, then the surface temperature of the immersion heater will be very high, , the internal temperature will inevitably rise, when the internal temperature of the heating tube is high to a certain extent, then the resistance wire will be burned out, the heating element is broken.
At the same time, the water scale will also prevent the surface temperature being absorbed by the water, which will have the same consequences.
Therefore, should be careful avoid dry burning, if the water condition is easier to scale, the anti-scale material should be selected. In this way, the water immersion heater can be used longer.
One disadvantage of copper immersion heater element is that it will be over heating ,when the thermostat has problem,it can still working and heating the water in the tank,this will lead to fire.To avoid this problem,the heating element should be assembled and maintained by a qualified professional, and to regularly check the thermostat to ensure it's working correctly.
The wattage of copper immersion heater range from 1500 to 5500 watts. High-density elements have a high level of wattage per square inch, which is why they get super hot.
When buying a new element, keep volts the same, and buy the same or less wattage. Always match the volts of the element to the volts on the heater itself. If you need to replace it, we suggest replacing it with a lower wattage, as long as the voltage is the same.

Advantage
T2 Copper Immersion Heating Elements heat up quickly and radiates heat evenly. It has good heat dissipation performance and high heat efficiency,long service life and small volume of heating device.
Can be customized according to customer requirements.
Process
Factory Equipment

Customer Feedback
![product-1-1 _]T]F%H2@Q`C}CMOFT66Z@R](/Content/uploads/2021739098/20211013151719115c3354faf543479fd288e3f6ca79f4.png)
![product-1-1 P1}QVN2ZT%`NS{9MF7[6]~B](/Content/uploads/2021739098/2021101315172659d8e58009bd4d399eab596036dcfbd9.png)

![product-1-1 Y7QSAO3ZUJVOVVZ]P{0(M1V](/Content/uploads/2021739098/202110131517511cb91898bbad43ae9b035eaa575050ec.png)

We make track record for each customer about the order status.So do not worry about the service and our cooperation!
Hot Tags: Copper solar water heater element, China, suppliers, manufacturers, factory, customized, wholesale, free sample, made in China, 4U Type Electric Immersion Water Heating Element, 220 V 2KW Stainless Steel Immersion Water Heater element, Green Treated Immersion Heating Element, solar immersion heating element, Boiler Water Flanged Immersion Heating Element, 24 volt water heater immersion element






























