Immersion Heater Element For Water Heater

Immersion Heater Element For Water Heater

Description Immersion heating element for water heater is brass flange heating element.The flange material is brass and the heating tube is SUS304.The power and voltage is 1500w and 220-240V ,the quality level is European standard. The length is 300mm and can be customized.The surface is...
Send Inquiry
Description

 

Description

 

Immersion heater element can be designed to different voltage and power.

It depend to different application.

 

The water heater element is the key to get hot water. But the lack of hot water is not the only indicator that you may need a new water heater element. It maybe rust, noises, and leaks coming from your water heater.

The type of water heater element you choose will depend on the voltage, wattage of your water heater, it is also related to the low-density or high-density of the heating element.

A low-density water heater element is made from copper, magnesium, and nickel. A high-density water heater element is typically the most affordable element you can purchase and install on your water heater. 

 

Although,the immersion water heater has its advantange,but it has its flaw.For example,it take too much time.If there is no thermostat or temperature control,it will be overheat and waste too much time,finally it will have some problem and you have to replace it.

Another advantage is that it is dependent from boiler or central heating system.If the boiler has problem,it can still work.

But immersion heater element has high operation cost ,especially in the high power condition.

 

For a long service life from your immersion heater, you will need to make sure that both the heater's sheath material and the power density of the elements are appropriate for your application. These specifications, of course, are in addition to finding the right wattage, which is the amount of power your heater needs to do its job. To sum up, for the best immersion heater possible, you'll need to do three things:

Specify the right sheath material for the fluid being heated,
Specify the right power density (that is, the watts per square inch or square centimeter).
Specify a wattage high enough to heat your fluid to the right temperature.

 

The material of the Immersion heater element for water heater can also be customized such as Copper,Stainless steel SS304,SS310,SS316,SS321,Inconel & Incolloy sheath.The tube diameter Ø 6.5 mm, Ø 7.5 mm Ø 8.5 mm,Ø 10 mm, Ø 14 mm,Ø 16 mm,Ø 18 mm,Ø 21 mm.

There are many uses of immersion heaters and using immersion heaters is quite simple. An immersion heater is used to heat a liquid inside a vessel. Sometimes they are used to heat gases as well.we make all our immersion heaters for various industries. Applications such as water heaters, oil warmers, and gas truck heaters are some of the industries we work with. We also manufacture various types of immersion heaters as well and everything is done.

 

We have strong engineer team, can supply enough technology support.And our best moulding ability let us can produce all special heaters OEM for you.If you have special shape and specification,we can open new mould for you based on your appointed drawing.

 

Concerning the topic that how long will it take immersion heater element to heat a water tank? It is depend on the tank size an how much water in contain,it is also related with the power of the heating element.

The ideal temperature for an water heater is recommended to be set at 50°C. The temperature is controlled by the  thermostat and heats it before it comes out from the taps.To heat an entire water heater, you can also purchase 14-inch, 18-inch, 27-inch, 30-inch, and even 36-inch immersion heater element.

 

Immersion heater element for water heater can be supplied with thermostat as a whole item or supplied seperately.

 

Before the design of the immersion heater,we must be clear about the following points:

1.The liquid heated is water or oil ,or other corrosion liquid.

2.When the immersion heater element is put into the equipment,how about the pressure it will endure?

3.It is assemble as horizontal or vertical.

4.The assemble space and the tank material.

product-719-526

 

 

The heating way of the water heater element can be single tube heating or double tube heating:

The single tube heating way is always used in the low level quality water heater ,the power is small. As it is single tube ,so the surface load is large,the warranty is short.

 

The double tube heating is always used in the high level quality water heater,the power is also larger.Heating efficiency is better,life is longer.Besides, the heating efficiency of the double tube heating also require the layout.If the layout is reasonable,it can achieve half tank and full tank,with more practicality and flexibility.

 

Deciding whether to replace individual components or the entire water heater tank can be a significant decision. While replacing heating elements is often sufficient for restoring function, certain situations warrant a complete tank replacement. Here are key indicators that it's time to replace the entire tank:

Age of the Heater: The average lifespan of a water heater is around 10-15 years. If your heater is approaching this age and is experiencing frequent problems, it might be more suitable to buy a new one.


Leaks in the Tank: If you find water pooling around the base of your water heater or corrosion , it's a sign of a leak. Then,you have to replace it.


If your water heater can not afford household hot water demands or takes too long to recover, it may be too small or losing efficiency, suggesting the need for an upgrade.

 

 

Hf422f1cb670a470d86bb66caf5e71aa7q

FAQ

Q: What's your MOQ?

A: Normally we accept order with 1,000pcs each model. For regular model, we also accept quantity below 1,000pcs.

Q: What's your delivery time?

A: About 25-30 days after deposit.

Q: After how many days can goods be delivered?

A: Our delivery time will be 25-30 days after deposit paid.

Q: How long will it take to arrive?

A: About 20-30 days by sea and 5-7 days by air.

Q: Can I get sample before order?

A: Yes. The sample fee and freight should be paid at your side. We will return the sample fee if order.


 


 

Hot Tags: Immersion Heater Element For Water Heater, China, suppliers, manufacturers, factory, customized, wholesale, free sample, made in China, Domestic Immersion heating element, 3000W Stainless Steel Electric Immersion Heater Element, 11 inch immersion heater element, 18 inch immersion heater element, 2500w Stainless Steel Hot Water Heater Immersion Element, Type G Stainless Steel Immersion heating element

Send Inquiry

Customer First

We transform your requirements into customer-centric, technologically advanced and economical solutions.