In the selection of injection molding machine heater, cartridge heater is a more common choice.
It is an essential component of the injection molding machine. Its performance and stability directly affect the production efficiency and product quality of the injection molding machine.Therefore, the diagnosis and maintenance of the heating tubes of the injection molding machine are of great significance.
Firstly, the faults of cartridge heater in injection molding machines usually manifest as insufficient heating or uneven heating. The causes of these problems may include aging of the heating element, malfunction of the temperature controller, poor contact, etc. When diagnosing the faults, the first step is to check whether the appearance of the heating element is damaged or aged. Secondly, it is necessary to check whether the temperature controller and wiring are normal. If a fault is found, it should be replaced or repaired in time.
Secondly, the maintenance of the cartridge heater in the injection molding machine is also very important. To extend the service life , regular cleaning and maintenance are necessary. Regular cleaning can prevent dust or grease from accumulating on the surface of the heating element, thereby ensuring the heating efficiency of the tubes. In addition, it is necessary to check whether the wiring of the heating tubes is tight and whether there are any damages or aging issues. If any damage or aging is found, it needs to be replaced in time
The advantage is as below:
1. High thermal efficiency: the design of the cartridge heater enables it to quickly heat the mold, saving production time and cost.
2.long life: made of high-quality materials and advanced technology, cartridge heating element can withstand high temperature and high pressure, and long service life.
3.Easy to install and maintain: its structure is simple, easy to install and maintain.
It can keep the temperature tolerance of the mold within ± 5 degrees. The more common embedded mold cartridge heater is usually straight type, with limit stop plates, right-angle bent ones, etc.
The cartridge heater for injection molding machine are also used in labeling machines, rice packaging bag sealing machines, mold heating, 3D printers, edge banding machine heating, etc.It can be equipped with K-type or J-type thermocouples for temperature detection.
The smallest diameter can be 3mm.
For the cartridge heater for injection molding machine, the most important thing is to ensure that the heat can be transferred to the heating medium in a timely manner, reducing the temperature of the internal material of the injection molding machine heating tube. This can effectively increase the service life of the heater.
During the usage process, we should pay attention to the following points
1) The gap between the outer diameter of the cartridge heater and its insertion hole diameter should be minimized as much as possible. Generally, the gap between the two is less than 0.2mm.
2) The installation holes should be able to fit the heating element. The deviation tolerance should be controlled within 0.05mm. If the deviation is too large, the processed holes need to be corrected.
3) Before installing, all impurities left in the mold holes should be thoroughly cleaned. If there are residues such as engine oil, they will be carbonized after heating, thereby affecting the heat conduction capacity.
Of course,to choose the appropriate injection molding machine heater,we should also consider the following factors:
1. Temperature range: Different elements are suitable for different temperature ranges. The appropriate temperature range should be selected according to the specific needs of the injection molding machine.
2.Power: The power of the heating element needs to match the size of the injection molding machine to ensure sufficient heating effect.
3.Material quality: the material quality is directly related to the life and effect of the heating tube, and the heater which is made of high-quality materials should be selected.
The heating principle of cartridge heater is: When current through the resistance, it will produce heat.
Thermal fuses can be built into injection molding cartridge heaters to act as a high limit for the heater in applications to avoid dangerous situations. When the trigger point is reached ,the thermal fuse will open,cutting the electrical current to the cartridge heater. Once the thermal fuse opens,it can not be reset. Many different trihher temperatures are available.
Recently, a customer came to tell me that he use the cartridge heater for heating the mold, this heater is bought from another factory, when the cartridge heater is connected to the electric, it broke in 20 minutes , the lead wire was broken.
So I asked him for a picture about the broken heater element, we can see that the lead wires are black, preliminary judgment it is caused by high temperature burned off. Then I asked him to measure the resistance , and the resistance value was normal, which showed that it was not the problem inside the mold cartridge heating element.
So I asked him for a picture of the burnt out electric heating tube, from the picture, the mold single-head electric heating tube lines are black, preliminary judgment is high temperature burned off. Then I asked him to measure the resistance value of the electric heating tube, and the resistance value was normal, which showed that it was not the problem inside the mold single head electric heating tube.
Then we'll find the causes from the power wire and the installation way.
1.Maybe the power wire can not withstand the high temperature and burned off.
The customer said that the manufacturer provided him with with a temperature resistance of 300 degrees, and the working temperature was only 200 degrees, so this is not the issue.
2.The assemble way is not reasonable.
Normal cartridge heater element for mold should meet the following:
1.The gap between the mold hole and heating tube should be less than 0.2mm.
2.The heating area of the cartridge heater should not go out of the mold hole.
3.Mold heater can not go through the hole too deep,resulting the lead wire into the hole.
According to my analyse,the customer find that he design the mold hole too longer than the heater,resulting the lead wire come into the hole.As we know that the temperature of the mold is conducted by cartridge heater,if the mold is over 200℃,the heater must be over 350℃,so the lead wire will be burned out.
So finally,we suggest the customer not put the wire into the hole,or a stop plate can be assembled on the cartridge heating element to avoid the problem.
When using the cartridge heating element,we should notice the following points:
1.When use it within the rated voltage range, do not use power above the rated voltage.
The resistance of the cartridge heater is fixed,more higer voltage than the rated will rise the power and abnormal temperature will cause the broken of the heater and even cause the fire.
2.Do not let the high power pencil heater work in the atmosphere
Even if part of the heating section is exposed to the air, it may cause wire breakage and fire due to abnormal heating.
3.Do not mechanically knock or transform the cartridge heater
Knocking and reforming may cause damage, short circuit, electric shock and other problems.
Monotube cartridge heating elements

PTC cartridge heating elements

High density/ultrawatt cartridge heating elements

Low density cartridge heating elements

Certification
Hot Tags: Cartridge heater for injection molding machine, China, suppliers, manufacturers, factory, customized, wholesale, free sample, made in China, Dependable Cartridge Heating element, Bended Immersion Cartridge Heating Element, Square Cartridge Heating Element, 24v DC cartridge Heating Element, Laboratory Still Heating Elements, 12v Dc 3d Printer Cartridge Heating Element






























