Screw In immersion heater

Screw In immersion heater

Electrical flange immersion heaters are designed for heating or temperature maintening of liquids, gas or mixture in static or circulation conditions.
Send Inquiry
Description

Description


The screw plug immersion heater consists of one, three or six heating elements which are assembled on a brass, steel or stainless steel plug. Main uses: Heating of flowing or static fluid such as water, oils, thermal oil.


We manufacture screw plug heaters to fit your requirements, including different sizes, materials, and wattage.


Screw In immersio heater is made by a metal tube as the shell, along the center of the tube axial distribution of spiral electric thermal alloy wire (nickel chromium, iron chromium alloy) ,screw plug heater's gap is filled with compact magnesia with good insulation and thermal conductivity, both ends of the tube mouth sealed with silica gel or ceramic.


Screw In immersion heater is a special electric component that converts electric energy into heat energy. As its cheap price, convenient use, convenient installation, no pollution, screw in immersion heater is widely used in various heating occasions. The service life of screw plug immersion heater is very long, and the general design service life is more than 10,000 hours.


1. Voltage can be designed as: 12-660V

2. Single injection power: 50W-20KW

3. Material: 10# iron, T4 copper, 1Cr18Ni9Ti stainless steel, Ti titanium, etc.

4. Specifications: U type, W type, special-shaped, with heat dissipation fin electric heating tube, explosion-proof electric heating tube


Maintenance 

1 For most applications, some heater maintenance is required.

2 Disconnect line switch prior to any testing or work on the heater

3 Check heater termination's after the initial 8 hours and tighten any looseterminal and jumper connections.

4 Recheck wiring periodically to ensure wiring has not become damaged,worn, or loose due to vibration or other application related conditions.Tighten, repair, or replace as needed.

5 Immersion heater should be checked periodically for scaling or mineraldeposits on heater tubes and cleaned as required. Initially, once a weekand thereafter once a month or longer.


Technical Data

Flange size

DN 50 to DN 800

Screw plug size

1"- 3"

Tube Diameter

8-16 mm

Immersion Length

150mm- 1500mm

Heating Element

3 elements, 4 elements, 6 elements, 10 elements etc under customer request

Wattage density

2-8W/cm2

Voltage

UP to 600V

Sheath Material

Stainless Steel 304 316L 310S Copper Incoloy 800 840

Built in thermostat well

Built-in thermostat wells can be installed upon request. When ordering, please provide length BUILT-IN THERMOSTAT WELL and internal diameter

How to choose the right Material for immersion heater?

Application

Sheath Material

Typical Watt Density(w/cm²)

Screw Plug/Flange Material

Water, Freeze protection, Hotwater storage, Boilerandwaterheaters, Coolingtowers, Solution not corrosive to copper, Food equipment

Stainless Steel304 316L or Copper

8w/cm2

Stainless Steel or Brass

Oil, Heavy and non-circulated oils, Solution water, Corrosive solutions, Steam super heating

Stainless Steel 316L 310s or Incoloy

2.5w/cm2

Stainless Steel

Light oils , Inforced oil circulation loops

Stainless Steel304 316L

4.5w/cm2

Stainless Steel

Mildly corrosive solutions

Stainless Steel 316L 310s or Incoloy

8w/cm2

Stainless Steel

Fluid heat transfer media, Tar, High to low viscosity petroleum oils, Asphalt, Wax, Paraffin, Degreasing solvents, Alcohol, Molten salt, Solutions not corrosive to steel

Stainless Steel304 316L

2.5w/cm2

Stainless Steel

Process water, Soap and detergent solutions, Soluble cutting oils, Demineralized or deionized water

Stainless Steel304 316L

4.5w/cm2

Stainless Steel

Please consult corrosion guide recommendations.

Product Application

Fuel and Oil Heaters Hot Water Storage Tanks

Warming Equipment Preheating All Grades of Oil

Food Processing Equipment Cleaning and Rinsing Tanks

Heat Transfer Systems Process Air Equipment

Boiler Equipment Freeze Protection of Any Fluid

20190909150916_17418

20190909151148681

FAQ

1. Q: How to Choose the System Voltage ?

A: We can design the heater element for 12v or 24v tubular heater or 220-380V for normal tubular heating eleemnt.

2. Q: Is there cheap shipping cost to import to our country?

A: For small order,express will be best, for bulk order,sea ship way is best but take much time.

For urgent orders,we suggest by express, big quantity by air.

3. Q: Can I get some samples ?

A: Yes, Sample orders welcomed.

4. Q: What is your minimum order quantity?

A: There's no minimum quantity ,you can buy any quantity. However, few in number, the unit price will be a little higher.

5. Q: How can I know the status of my products ?

A: We will keep you posted for the every production progress like material purchasing, production status, delivery time, tracking number until you recieved the products.

6. Q: Can You Give Me Help If My Products are Very Urgent?

A: Yes, Of Course, We Will Try Our Best to Give You Help. Because We Have Our Own Factory to Produce. We Can

Hot Tags: Screw In immersion heater, China, suppliers, manufacturers, factory, customized, wholesale, free sample, made in China, 4500 Watt High Density Screw in Water Heater Element, camco screw in water heater element, AC 380V 6KW Metal Screw in water heating element, Screw In Ceramic Heating Element, HOT WATER TANK SCREW TYPE HEATING ELEMENT, 1 SCREW IN WATER HEATER ELEMENT

Send Inquiry

Customer First

We transform your requirements into customer-centric, technologically advanced and economical solutions.